Steering Parts
- 1
- 2
-
-
- This rudder is a must for small boats, 19' and under
- Easy to control your boat at low speeds, especially near the dock
- Easier to align the boat when putting on the trailer
- 5-1/2" ht. x 8" lg.
- Includes a pin and two bolts
- Made of aluminum
- Fits any Place Diverter
- Older model Place Diverters require drilling two 1/4" tapped holes and bolt up
- Newer model Place Diverters are pre-drilled for these rudders, bolt up
-
-
- This arm mounts to the steering pin on your nozzle with an allen screw (included)
- Fits all Aggressor, American Turbine, Berkeley 12JA, 12JB, 12JC, and 12JG, Dominator, Legend, and Volvo Penta pumps with a single steering pin
- Will not fit JE and JF Pumps. For Berkeley 12JE and 12JF see Steering Arms for Berkeley 12JE and 12JF Pumps
-
- Also known as rod end bearings
- Sold per Each
-
- This bracket replace the standard Place Diverter steering arm when using Calgo Steering.
- Has a built in adjustable stop
- For hydraulic cylinder control diverter
-
The is cable end steering swivel is made of alumimum. The steering swivel also has a brass bushing.
-
- Includes: steering swivel and riser tube
- Riser Tube is 2 inches tall
Need the entire kit with steering extension click here
-
These Max Grip Stainless steel steering wheels have a shiny black plastisol coating. Easy to grip for tight turns or racing fast.
Choose from a Standard depth or Deep depth.
12" diameter wheels are available in Standard Depth or Deep Depth
13" diameter wheel is only available in Standard Depth
Standard depth is approx 2-3/8".
Deep depth is approx 4".
Steering Hub Adapter Sold Separately See related items below
-
Encapsulated o-ring fits fiberglass boats with SD312 American Turbine jet pumps.
-
- FEATURES
BETTER REVERSE THRUST (STRAIGHT BACK PULL)
REVERSE SENSE STEERING
MUCH IMPROVED HANDLING IN REVERSE
EXCELLENT CONTROL WHILE DOCKING AND LOADING / UNLOADING
EASILY SHIFTS INTO REVERSE AT HIGH IDLE RPM
GREAT EMERGENCY BRAKING
OPERATES WITH SIMPLE OUTBOARD LIKE THROTTLE / SHIFT CONTROL
USES INEXPENSIVE 40 SERIES SHIFT CABLE
WHEN IN REVERSE WATER DOES NOT RE-CIRCULATE INTO JET INTAKE
THRUST IS DIRECTED UNDER BOAT WHEN IN REVERSE
WILL FIT ON SD309, SD312, AT309, 12-S, 12TD, BERKELEY SET-BACK
- Fits American Turbine Jet Pumps
- Fits Dominators
- Fits Berkeley with split bowl
- Fits Jacuzzi Energizer
- Fits Panther Jet Energizer
- Can be bolted to the following:
- Split Bowl
- Long or short extension housing
- FEATURES
-
Lower cable control bellows.
Sold by the each.
-
- Pin Bushing 3/4" nyliners
- Also fits Place Diveters
- Sold per pair
Standard
- Color is white nylon
High Performance
- Color is grey
- More abrasion resistant than white nylon
- Low Friction Finish (Slippery)
-
- Pin Bushing 3/4" Nyliners
- High Performance Grey
- Sold per pair.
-
- 1/2" dia pin
- Sold per pair
- Also known as flanged pin bushing liners
-
- 1/2" pin size, 1/4" Length under flange
- Sold per pair
- Also known as flanged pin bushing liners
-
- 3/8" pin size
- Sold per pair
- Also known as flanged pin bushing liners
-
-
Bushing is made of white nylon. Bushing is sold per each.
-
-
-
-
-
-
-
-
-
-
-
-
• Three spokes are brushed aluminum
• 13.8" diameter
• An attractive addition to any boat
• The perfect wheel for competition or fun
• Color is black
-
These Helm wedges allow you to angle your steering helm. Kit includes Two 10' Wedges & Bolts.
-
Steering wheel center cap assembly.
-
Steering Wheel Hub Adapter for 3/4" Standard Taper.
-
Complete assembly (as pictured).
-
Steering tube only. Made of black aluminum.
-
2 required.
Sold per each.
-
Expandable rubber tube that creates a seal.
-
Steering Cable Thru Hull Tube (End cap with grease zerk).
-
1 left in stock
Steering set back install kit contains a transom bezel, steering tube, steering extension, steering clevis swivel and a shift control cable packer. All aluminum parts are made from billet aluminum and are anodized.
-
Allows for up/down missaligment on diverter side of steering cable.
-
A must when adding a droop snoot or bowl extension.
- Length is measured center-to-center
Need a complete kit? Our steering extension kits
-
- A direct replacment for your old worn out Berkeley droop snoot
- A Droop Snoot is designed to create lift on the aft end of the boat, by lowering the thrust line of the jet nozzle
- Actual drop in Nozzle height is 1 1/8"
- The Nozzle / Pin angle is 7 Degrees up
- Works well on boats less than 20’
- Requires 1 pair of plastic nyliners (See related products below)
- Requires a 4-1/8" steering extension — Our Extension Kit is the best bang for your buck and includes everything needed for proper instalation (See related products below)
- American Turbine
- Can be bolted to the following:
- Split Bowl
- Long or short extension housing
- Bowl transition adapter or rooster booster
-
- American Turbine steering/reverse nozzle with rudder
- Fits late model American Turbine (without the ball type nozzle housing), Dominator, and Berkeley jet drives
- Comes complete from the steering pins back
- Will also fit some other jets but please inquire first
-
- N.O.S. "New Old Stock" Berkeley steering assemblies
- Keep that Original Berkeley look!!
- Includes —Steering/reverse nozzle with aluminum rudder
- Comes complete from the steering pins back
- Fits Berkeley jet drives without Jetovator
- Will also fit some other jets but please inquire first
-
- Fits Berkeley jet pumps
- Made of aluminum
-
- Fits American Turbine and Dominator jet pumps
- Made of Aluminum
- For 3-Bolt mounting setups
-
- Fits American Turbine trim nozzles
- Made of aluminum
- 4-Bolt mounting setups
-
- Designed to improve low speed maneuverability and control
- Works great on boats 19' and longer
- 7" ht. x 12" lg.
- Includes a pin and two bolts
- Made of aluminum
- Fits any Place Diverter
-
Not recommend for use with droop snoots
Installation: - Older model Place Diverters require drilling two 1/4" tapped holes and bolt up
- Newer model Place Diverters are pre-drilled for these rudders, bolt up
-
- Sold by each
-
-
- Made of stainless steel
-
-
-
-
-
-
-
• Fits 1/4"-28 Thread Size
•Fits 43C and 43BC Cables
-
-
- Made of stainless steel
-
-
This 7" steering extension kit is all you need.
- Kit is designed to be used with Berkley Style Droop Snoot Housing
- Includes: steering swivel, riser tube, and steering tube Extension
Need just the steering swivel and riser tube click here?
-
-
If you have the hp to create lift, this snoot is for you. It adds just the little extra lift you need.
- Factory replacement for American Turbine
- Can be bolted to the following:
- Split Bowl
- Long or short extension housing
- Bowl transition adapter or rooster booster
-
-
Made of stainless steel.
-
-
-
-
Steering Cable Seal O-Rings — Fits HTR II Steering & most Transoms
-
-
-
-
-
-
-
-
-
- 1
- 2