Fits Place Diverter Brand
-
- Also known as rod end bearings
- Sold per Each
-
- This bracket replace the standard Place Diverter steering arm when using Calgo Steering.
- Has a built in adjustable stop
- For hydraulic cylinder control diverter
-
The is cable end steering swivel is made of alumimum. The steering swivel also has a brass bushing.
-
- Includes: steering swivel and riser tube
- Riser Tube is 2 inches tall
Need the entire kit with steering extension click here
-
- Mounts to the side of your Place Diverter, with 3 allen screws. Other bolt hole is for the heim joint.
- Fits all style Place Diverters
- Color is raw aluminum
-
Choose from the following setups:
- Manual ready control
- Hydraulic ready control
- Hydraulic ready control with cylinder (picture shown)
Options available : Fine tune nozzle insert
For boats with a swim platform, the bend in the control cable to the place diverter might be too sharp of a curve to operate properly. We recommend a complete hydraulic ready kit which includes everything you need for a do-it yourself installation.
-
- Kit provides freedom of instant control with the flip of a switch
- Unit travels its full range in approximately 2 seconds and infinitely adjustable
- Place Diverter Brand
Each kit includes:
- Hydraulic diverter assembly
- Hydraulic pump
- Wiring harness
- Switch
- Brass Compression Fittings
- Plastic hydraulic lines
- Water tight fittings (pair)
- Cylinder with stainless steel heim end (rod bearing)
- Dovetail mounting backet
- In-line fuse
- 3-way electrical switch
- Note: Berkeley JF pump includes a steering extension
Options available : Fine tune nozzle insert
-
- Provides instant control with the push of a lever
- Place Diverter Brand
Each kit includes:
- Floor or stringer mount control
- 14', 15' , or 16' cable
Note: Berkeley JF pump includes a steering extension
Options available : Fine tune nozzle insert
For boats with a swim platform, the bend in the control cable to the place diverter might be too sharp of a curve to operate properly. We recommend a complete hydraulic ready kit which includes everything you need for a do-it yourself installation.
-
Choose from the following setups:
- Manual ready control
- Hydraulic ready control
- Hydraulic ready control with cylinder (picture shown)
Berkeley JF includes a steering arm that is needed for complete installation
Options available : Fine tune nozzle insert
For boats with a swim platform, the bend in the control cable to the place diverter might be too sharp of a curve to operate properly. We recommend a complete hydraulic ready kit which includes everything you need for a do-it yourself installation.
-
- Pin Bushing 3/4" Nyliners
- High Performance Grey
- Sold per pair.
-
- Do-it-Yourself rebuild kit is everything you need
- Includes:
- Nyliners (4-standard length, 2-short length)
- PTFE O-ring
- Double PTFE seal
-
- Riser for Place Diverter steering
- Made of Aluminum
-
- Choose from (Sold per Pair):
- 1 Rudder Pin and 1 Steering Pin (For place diverters with rudder)
- Steering Pins (For Place Diverers without a rudder)
- Reverse Gate Pins (For Place Diverters with or without a rudder)
- Nozzle End Pins (For Place Diveterters with or without a rudder)
Bolts are not included, but, you can add them in the click box.
- Made of stainless steel
- Fits Place Diverters
-
- Mounts to the side of your Place Diverter.
- Also known as E-steering plate
- Optional Flat head screws (2) attach the steering plate to the diverter.
- Optional Hex head screws (2) attach stainless steering arm to the steering plate.
- This steering plate is used on the Berkeley 12JE and 12J Place Diverters
-
- Mounts to the side of your Place Diverter, with 3 allen screws. Other bolt hole for the heim joint.
- Also known as E-short control arms
- This control arm is used on the Berkeley 12JE, 12JF or the LPS Model Place Diverters
-
- Use this arm to attach your reverse bucket (gate) to your reverse bucket (gate) cable
- This reverse side arm is used on the Berkeley 12JE, 12JF or the LPS Model Place Diverters
- Also known as E-reverse side arms
-
- This steering arm has an extra offset to keep the steering cable straighter
- Offers a slightly higher steering connection
- Steering standard arm mounts to the top of your Place Diverter with 2 allen screws
- Great for hooking up an American Turbine steering assembly or American Turbine transom housings
- Available in manual control or hydraulic control
- Fits all Aggressor, American Turbine, Berkeley 12JA, 12JB, 12JC, and 12JG, Dominator, Legend, and Volvo Penta
-
- Steering standard arm mounts to the top of your Place Diverter with 2 allen screws (not included)
- Available in manual control or hydraulic control
- Fits Berkeley 12JE and 12JF
-
Also known as E-steering arms
-
- Mounts to the side of your Place Diverter, with 3 allen screws. Other bolt hole is for the heim joint.
- Fits all style Place Diverters
-
- Steering standard arm mounts to the top of your Place Diverter with 2 allen screws
- Available in manual control or hydraulic control
- Fits all Aggressor, American Turbine, Berkeley 12JA, 12JB, 12JC, and 12JG, Dominator, Legend, and Volvo Penta
-
For Berkeley 12JE and 12JF see Steering Arms for Berkeley 12JE and 12JF Pumps
-
- This reverse gate is used on the Berkeley 12JE, 12JF or the LPS Model Place Diverters
- Only difference in the LPS Bucket is the side hole is a different size
- Also known as E-reverse bucket
-
- Standard ball assembly
- Replaces most worn out Place Diverter ball assemblies
-
- End nozzle only, with the patented built-in-ride plate
- Fits any year or model Place Diverter
-
- Fits any year or model Place Diverter
- Fits all Aggressor, American Turbine, Berkeley 12JA, 12JB, 12JC, and 12JG, Dominator, Legend, and Volvo Penta
For Berkeley 12JE and 12JF see Reverse Buckets for Berkeley 12JE and 12JF Pumps
-
- Mounts to your dash, for easy finger tip control
- For use with Place Diverter or American Turbine Diverters
-
Kit includes:
- Hydraulic pump wire harness
- Hydraulic pump plastic line (approx. 14')
- Stainless steel cylinder with rod bearing end (heim)
- Dovetail mounting bracket and hardware
-
1 left in stock
- Hydraulic pump used to control Place Diverters or American Turbine Diverters.
- Specially designed to for Place Diverters with 4 solenoid valves. The extra 2 solenoids hold the up or down position in place.
- Very dependable
Easy to install
-Fill with any type of transmission fluid
-Turn the switch up and down about six times
-Line will self bleed
Includes hydraulic pump only
-
- Stainless Steel cylinder
- Picture shows:
Optional brass compression fittings
Optional prod end bearing (heim end)
Optional top mount bolt and nut
- Can be used with air for many other functions such as exhaust flapper control, or reverse bucket controls
- Fits Place Diverter or American Turbine Diverter
-
- Cover fits all Place Diverter or American Turbine Diverter hydraulic pumps
- Replace your cracked cover, with a nice new one
-
- Everything you need to mount your hydraulic pump to your boat
-
- Ultimate braided line kit runs from the Droop Snoot or Nozzle Housing to the Transom
- Aircraft quality stainless steel lines, includes everything to install your existing diverter
- Includes bulk head fittings, just drill your transom to install and reconnect lines to cylinder
Choose from two Styles:
- For Standard Nozzle Housings — Includes 22" and -26" length hoses
- For Droop Snoots — Includes 30" and 34" length hoses
Choose from two Fitting Styles:
- All stainless steel hydraulic lines
- Stainless steel to plastic lines]
Also availble:
- Inside Kit includes 2 hydraulic lines connecting the transom to the hydraulic pump, two 90° fittings for the pump, and two flared bulk head fittings
- Complete kit — Includes:
4 stainless steel hydraulic lines. Two from the nozzle housing or droop snoot to the transom. Two additional from the transom to the hydraulic pump.2 bulk head fittings, just drill your transom to install and reconnect lines to cylinder
Four 90° Fittings
-
- Made of Stainless steel
- Includes two wood screws
- Also known as cable packing seals
-
Complete assembly (as pictured).
-
A must when adding a droop snoot or bowl extension.
- Length is measured center-to-center
Need a complete kit? Our steering extension kits
-
- Made of high pressure plastic tubing
- Connects your hydraulic pump to your cylinder
- Approximate 14' length
-
- 7-position control
- Includes hardware for cable installation
- Use for rooster tail adjustment
- Place Diverter Brand
- Cable is not included
-
- 7-position control
- Use for rooster tail adjustment
- Includes hardware for cable installation
- Place Diverter Brand
- Cable not included
-
- For manual or hydraulic control place diverters
- Place Diverter brand
-
- These brass fittings go on the Place Diverter or American Turbine hydraulic cylinder
- Made of brass
- Sold per pair
-
- These brass fittings go on the Place Diverter or American Turbine hydraulic cylinder
- Made of brass
- Sold per pair
-
Easy to install:
- Drill two 7/16" dia. holes in your transom, or transom adapter ring
- Use a 1/2"-20 tap to thread holes
- Apply Life Seal (silicone) to threads of fitting,and screw into threaded holes
- Slide tubing through hole and when at desired length turn outer lock nut tight
Sold per pair
-
- 3.5° degree nozzle housing
- 1/2" drop transition
- Housing has a hard flow chamber designed to deliver maximum thrust
- Place Diverter High Performance nozzle Housing
-
- Nozzle O-ring for steering nozzle
- Not sure which thickness you need????? Go grab two nickels and a quarter.
- If all this change fits in the slot then you need the 7/32" oring (see second picture).
- If only two nickels fit order the 1/8" one.
- If the nickel/quarter method doesn't work for you, give us a call at 815-942-2600 and we can help you.
-
- This is the inner PTFE o-ring in a Place Diverter
- When the o-ring goes bad it looks like a drinking straw hanging out of the Place Diverter
-
- This rudder is a must for small boats, 19' and under
- Easy to control your boat at low speeds, especially near the dock
- Easier to align the boat when putting on the trailer
- 5-1/2" ht. x 8" lg.
- Includes a pin and two bolts
- Made of aluminum
- Fits any Place Diverter
- Older model Place Diverters require drilling two 1/4" tapped holes and bolt up
- Newer model Place Diverters are pre-drilled for these rudders, bolt up
-
- Designed to improve low speed maneuverability and control
- Works great on boats 19' and longer
- 7" ht. x 12" lg.
- Includes a pin and two bolts
- Made of aluminum
- Fits any Place Diverter
-
Not recommend for use with droop snoots
Installation: - Older model Place Diverters require drilling two 1/4" tapped holes and bolt up
- Newer model Place Diverters are pre-drilled for these rudders, bolt up
-
- With a touch of the up / down button it provides ultimate trim control from the steering wheel
- Use on hydraulic jack plates, Place Diverters, trim tabs, or motor trim
- Includes 11" curly cord which can stretch to 48" uncoiled
- Easily mounts to the steering wheel or dashboard.
- Includes instructions, fasteners, wire nuts and "diodes"
-
- Up / down momentary push button
- 18" straight cord wiring harness
- Use on applications such as hydraulic jack plates, trim tab or motor trim
- Does not include diodes.
- We also offer a curly cord diverter switch with diodes.
-
- Pin Bushing 3/4" nyliners
- Also fits Place Diveters
- Sold per pair
Standard
- Color is white nylon
High Performance
- Color is grey
- More abrasion resistant than white nylon
- Low Friction Finish (Slippery)
-
- Made of stainless steel
-
- Also known as rod end bearings
-
This 7" steering extension kit is all you need.
- Kit is designed to be used with Berkley Style Droop Snoot Housing
- Includes: steering swivel, riser tube, and steering tube Extension
Need just the steering swivel and riser tube click here?
-
- Includes all items pictured
- For use on Place Diverters
- Does not include Gauge
-
Push button activated steering wheel controlled C02 solenoid valve fits Ram Horn Reverse Buckets, Long Horn Neutral Buckets, and can be modified to fit Place Diverters (also can fit American Turbine Diverters)
Kit includes:
- Push button steering wheel control
- C02 solenoid valve
- Relay assembly
- 15' wiring harness
- Attached to mounting plate
-
- Ultimate braided line kit is contains quality stainless steel lines and everything to install your existing diverter
- Includes:
- 4 stainless steel hydraulic lines. Two from the nozzle housing or droop snoot to the transom. Two additional from the transom to the hydraulic pump.
- 2 bulk head fittings, just drill your transom to install and reconnect lines to cylinder
- Four 90° Fittings
Choose from two Styles:
- For Standard Nozzle Housings — Includes 22" and -26" length hoses
- For Droop Snoots — Includes 30" and 34" length hoses
Choose from two Fitting Styles:
- All stainless steel hydraulic lines
- Stainless steel to plastic lines
Also availble:
- Inside Kit includes 2 hydraulic lines connecting the transom to the hydraulic pump, two 90° fittings for the pump, and two flared bulk head fittings
- Outside Kit includes 2 hydraulic lines connecting the Droop Snoot or Nozzle Housing to the Transom, two 90° fittings , and two bulk head fittings
-
- This flat head allen screws fits all Place Diverter Steering arms that mount to the top of the Place Diverter.
- Sold by the each
- Usually two screws are needed