Fig. No. | Description | Qty. Required | Mfg. No. | Fig. No. | Description | Qty. Required | Mfg. No. | |
---|---|---|---|---|---|---|---|---|
1 | Aluminum Impellers | 1 | IMB**A | 28 | Glacier Bowl Bearings | 2 | B1502 | |
1 | Stainless Steel Impellers | 1 | IMB**A | 29 | Bearing Cap Seals | 1 | SL1007 | |
2 | Bowls | 1 | SC9102 | 30 | Bowl Seals | 1 | SL2003 | |
3 | Suction Piece | 1 | H-1727 | 31 | 3/4" Nyliner Bearings | 4 | B2007 | |
4 | Hand Hole Covers | 1 | M-4128 | 32 | Thrust Bearings | 1 | B1007 | |
5 | Nozzle Housings | 1 | R1007 | 33 | Shaft Snap Rings | 1 | SH1507 | |
6 | Steerable Nozzle | 1 | L-4501 | 34 | Impeller Nuts | 1 | SH3507 | |
7 | Packing Gland Followers | 1 | SC2507 | 35 | 5/16" Pin with Grooves | 2 | S-14479 | |
8 | Bearing Caps | 1 | SC2007 | 36 | 1/4" Grease Fittings | 1 | S-14480 | |
9 | Reverse Bucket | 1 | L-4251 | 37 | Impeller Keys | 1 | SH3007 | |
10 | Pump Shafts | 1 | SH1107 | 38 | Woodruff Keys | 2 | R5507 | |
11 | Bowl Bearing End Caps | 1 | SCA9001 | 39 | 3/8"-24 Locknuts | 1 | S-26431 | |
12 | Shaft Sleeve Slinger Rings | 1 | SH2507 | 40 | 3/8"-24 x 2" HHCS | 2 | F06 24 16 HH | |
13 | SS Wear Rings | 1 | WR5000 | 41 | 3/8"-24 Thin Locknuts | 2 | F06 24 TL | |
13 | Bronze Shouldered Wear Rings | 1 | WR5000 | 42 | 5/16" Spring Lock Washers | 11 | F05 LW | |
14 | Plastic Insulators | 1 | WR6004 | 43 | 1/2"-13 x 1-1/4" HHCS | 8 | F08 13 10 HH | |
15 | Tiller Shaft | 1 | S-15396 | 46 | 5/16"-18 x 1" SCHS | 3 | F05 18 08 SH | |
16 | Pins | 2 | BN2510 | 47 | 3/8"-24 Locknuts | 1 | S-23665 | |
17 | Bowl To Nozzle Housing Gaskets | 1 | G2507 | 48 | Barbed Connectors | 1 | S-14821 | |
18 | Bowl To Suction Gaskets | 1 | G2006 | 49 | 5/16" Flange Nuts | 2 | S-23680 | |
19 | Bearing Cap Gaskets | 1 | G1502 | 50 | Fastener, Lock Wrench | 1 | S-14493 | |
20 | Nozzle O-Rings | 1 | O1502 | 51 | Fastener Screw | 2 | S-25599 | |
22 | Wrench, Hand Hole Cover | 1 | S-11543 | 52 |
-
1 left in stock
These kits include everything you need to rebuild your jet pump.
Most Kits include:
- Bearing cap gasket
- Bearing Cap Seal with stainless steel spring
- Bearing snap ring
- Bowl bearings (2)
- Bowl gasket
- Bowl o-ring
- Bowl Seal with stainless steel spring
- Graphite rope packing rings (5)
- Hand hole cover o-ring
- Impeller nut
- Impeller shims
- Insulator
- Nozzle housing gasket
- Nozzle o-ring - PTFE
- Nyliner bearings (4)
- Suction Housing Shaft Seal with stainless steel spring
- Suction housing to intake gasket
- Transom gasket
- Non-shouldered stainless steel wear ring – (upgrade available to stainless steel or bronze shouldered wear rings)
- Standard Thrust Bearing (Koyo Brand) — (upgrade available to Extreme duty)
-
These kits include everything you need to rebuild your jet pump.
Most Kits include:
- Bearing cap gasket
- Bearing Cap Seal with stainless steel spring
- Bearing snap ring
- Bowl bearings (2)
- Bowl gasket
- Bowl o-ring
- Bowl Seal with stainless steel spring
- Graphite rope packing rings (5)
- Hand hole cover o-ring
- Impeller nut
- Impeller shims
- Insulator
- Nozzle housing gasket
- Nozzle o-ring - PTFE
- Nyliner bearings (4)
- Suction Housing Shaft Seal with stainless steel spring
- Suction housing to intake gasket
- Transom gasket
- Non-shouldered stainless steel wear ring – (upgrade available to stainless steel shouldered or bronze shouldered wear rings)
- High Performance Thrust bearing
-
- Recommended for up to 450 h.p.
- See Stainless Steel Impellers for 450 h.p or more
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller
Impeller Selection Chart
-
- Recommended for 450+ h.p.
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller
-
- Aftermarket American Turbine Bowl
- Color is white
- Available in two choices
- Standard — 400 h.p. or less
- High Performance 400 h.p. or more
Please note the transom housing must be machined to fit the High Performance Bowl. If you want us to machine your transom housing click optional machine my transom housing for this bowl and I will send you my transom housing. [return shippimg charges will be included at checkout]
-
- This custom filled fitting Hand hole cover is designed for RACE USE ONLY.
- The cover fits the contour of the suction housing almost perfect thus leaving no room for air to get trapped around the cover that creates cavitation
- (Requires machining locator nub out of suction housing)
- Fits Berkeley JC and Berkeley JG jet drive pumps (Not OEM) It's aftermarket
-
-
- This is the piece that is behind the thrust bearing
- It usually breaks due to over tightening
- Sold per pair
-
-
High Performance Jet Pump Shaft
- For use in pumps not exceeding 400 h.p.
- Fits Berkeley, American Turbine, and Dominator
Extreme Duty Jet Pump Shaft — Made in the USA
- For use in pumps over 400.h.p.
- The bowl bushing area on the shaft is hard chrome to extend the life of the shaft. This keeps the seal and bushing areas from wearing into the stainless steel.
- 17-4 Jet pump shaft, is known to be the strongest in the industry
- A must for anyweekend warrior or your all out blown alcohol jet boat
- Fits Berkeley, American Turbine, Dominator
Optional Inducer Machining
- Click the optional box below and we will machine your shaft for an inducer.
-
-
-
- Create a double seal with these shouldered wear rings
- Over sizes available to fit your used impeller
- Fits American Turbine, Aggressor, Berkeley, and Dominator Late Model (1" skirt length) jet drive pump with new impeller
- A "standard" size wear ring is 7.250"
-
- Create a double seal with these shouldered wear rings
- Over sizes available to fit your used impeller
- A "standard" size wear ring is 7.250"
-
- Designed to effectively hold the wear ring in place
- Also known as wear ring liners
-
- Made of stainless steel
-
-
-
-
-
- 3/8" Heavy Duty Hand Hole Cover Eye Bolts are Recommended for use on "RACE Application Pumps"
- Fits Berkeley pumps and American Turbine SD312 jet pumps
- Includes:
- Billet eye bolts
- Clevis Pins
- Cotter Pins
- Thick Washers
- Lock Washers
- Wing Nuts
-
- Most jet pumps use 4 to 5 rings
- Sold per set of 5
-
- Hand hole cover O-ring
-
- Suction piece clipper seal
-
- Made of stainless steel
-
- Glacier bowl bearings
- Bowl bushings
- Sold per each
-
- Driveshaft or bearing cap seal
-
-
- Pin bushing 3/4" nyliners
- Sold per pair
- Also fits Place Diveters
-
Economy
- Up to 350 horsepower
- Double row of balls
Standard
- For use on moderate applications up to 450 horsepower
- Double row bearing, 8 balls per row 16 total
Extreme Duty
- For use on 500+ horsepower
- Use in High Horsepower applications where severe axial thrust loads are present.
- 11 ball double row angular contact bearing
Filling slot faces motor
Care must be taken when installing bearing onto shaft, only press on inner race of bearing
-
-
- Choose: Steel or billet machined hard anodized aluminum
- Loctite® is recommended
-
-
-
-
- Made of stainless steel.
-
- Made of stainless steel
-
Made of stainless steel.
-
- Made of stainless steel
-
- Made of stainless steel
-
- Made of stainless steel
-
- Made of stainless steel.
-
-
- Made of stainless steel
-
-
- Made of stainless steel
-
Made of stainless steel.
-
- Made of Stainless Steel
-