Fig. No. | Description | Qty. Required | Mfg. No. | Fig. No. | Description | Qty. Required | Mfg. No. | |
---|---|---|---|---|---|---|---|---|
1 | Reverse Bucket | 1 | L-4433 | 47 | 1/4"-20 x 2" FHMS | 3 | F04 20 16 FH | |
2 | Nozzle | 1 | L-4405 | 48 | Reverse Cable Seal Bearing | 2 | S-16254 | |
3 | 5/16"-18 x 1" HHCS | 4 | F05 18 08 HH | 49 | 7/8"-14 Jam Nuts | 1 | S-16347 | |
4 | 5/16" Spring Lock Washers | 22 | F05 LW | 50 | Flat Washer (7/8) | 2 | S-27129 | |
5 | 3/4" Nyliner Bearings | 4 | B2007 | 51 | Hose Clamp | 2 | S-16416 | |
6 | Pins | 3 | BN2510 | 52 | 5/16"-18 x 3/4" FHCS | 2 | F05 18 06 FH | |
7 | Bowl Bearing End Caps | 1 | SCA9001 | 53 | Cavitation Plate | 1 | S-16567 | |
8 | Glacier Bowl Bearings | 2 | B1502 | 54 | Steering Adapter | 1 | S-16273 | |
9 | Oil Reservoir Pipe Plugs | 2 | SC9902 | 55 | Reverse Cable Seal Housing | 1 | S-16274 | |
10 | Bowl Seals | 1 | SL2003 | 56 | Reverse Cable Seal Retainer | 1 | S-16255 | |
11 | Impeller Nuts | 1 | SH3507 | 57 | O-Ring (7/16 I.D. x 5/8 O.D.) | 1 | S-14929 | |
12 | Bowl | 1 | H-2484 | 58 | Hose Clamp | 2 | S-16415 | |
13 | Impeller Keys | 1 | SH3007 | 59 | Rubber Cable Control Bellows | 2 | M4007 | |
14 | Aluminum Impellers | 1 | IMB | 60 | 5/16"-18 x 2" FHCS | 2 | F05 18 16 FH | |
Stainless Steel Impellers | 61 | Cavitation Plate Bracket | 1 | M-5840 | ||||
15 | Bowl To Suction Gaskets | 1 | G2006 | 62 | Steering Extension | 1 | M-5881 | |
16 | 1/2"-13 x 1-1/4" HHCS | 8 | F08 13 10 HH | 63 | Flat Washer (3/8) | 3 | S-23063 | |
17 | Plastic Insulators | 1 | WR6004 | 64 | Hex Self-Locking Nut | 2 | S-32400 | |
18 | SS Shouldered Wear Rings | 1 | WR5000 | 65 | 3/8"-24 x 1-1/2" HHCS | 1 | F06 24 12 HH | |
18 | Bronze Shouldered Wear Rings | 1 | WR5000 | 66 | 3/8"-24 Hex Nuts | 1 | F06 24 HN | |
19 | O-Ring | 1 | O1002 | 67 | Shoulder Screw | 1 | S-17824 | |
20 | Pin, Groove, Type 24 | 2 | S-14479 | 68 | Cotter Pin (3/32 x 1/2) | 1 | S-26611 | |
21 | Hand Hole Cover Eye Bolt Kits | 2 | S-10907 | 69 | Clevis Pin (5/16) | 1 | S-16350 | |
22 | Wing Nut | 2 | S-16117 | 70 | Reverse Cable, Clevis | 1 | S-17843 | |
23 | 5/16" Flat Washers | 22 | F05 FW | 71 | Steering Tiller | 1 | M-5875 | |
24 | Hand Hole Cover | 1 | M-6098 | 72 | 5/16"-18 x 3/4" HHCS | 2 | F05 18 06 HH |
-
These kits include everything you need to rebuild your jet pump.
Most Kits include:
- Bearing cap gasket
- Bearing Cap Seal with stainless steel spring
- Bearing snap ring
- Bellows, cable control (2)
- Bowl bearings (2)
- Bowl gasket
- Bowl Seal with stainless steel spring
- Graphite rope packing rings (5)
- Hand hole cover o-ring
- Impeller nut
- Slinger Ring
- Impeller shims
- Insulator
- Nozzle housing gasket
- Nozzle o-ring - PTFE
- Nyliner bearings (4)
- Suction Housing Shaft Seal with stainless steel spring
- Suction housing to intake gasket
- Non-shouldered stainless steel wear ring – (upgrade available to stainless steel shouldered or bronze shouldered wear rings)
- Standard Thrust Bearing (Koyo Brand) — (upgrade available to Extreme duty)
-
1 left in stock
These kits include everything you need to rebuild your jet pump.
Most Kits include:
- Bearing cap gasket
- Bearing Cap Seal with stainless steel spring
- Bearing snap ring
- Bellows, cable control (2)
- Bowl bearings (2)
- Bowl gasket
- Bowl Seal with stainless steel spring
- Graphite rope packing rings (5)
- Hand hole cover o-ring
- Impeller nut
- Impeller shims
- Insulator
- Nozzle housing gasket
- Nozzle o-ring - PTFE
- Nyliner bearings (4)
- Suction Housing Shaft Seal with stainless steel spring
- Suction housing to intake gasket
- Non-shouldered stainless steel wear ring – (upgrade available to stainless steel shouldered or bronze shouldered wear ring)
- High Performance Thrust bearing
-
Made of stainless steel.
-
- Made of stainless steel
-
- Pin Bushing 3/4" nyliners
- Sold per pair
- Also fits Place Diveters
-
- Made of stainless steel
-
-
- Glacier bowl bearings
- Bowl bushings
- Sold per each
-
-
-
- Choose: Steel or billet machined hard anodized aluminum
- Loctite® is recommended
-
-
- Recommended for up to 450 h.p.
- See Stainless Steel Impellers for 450 h.p or more
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller
Impeller Selection Chart
-
- Recommended for 450+ h.p.
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller
-
-
- Made of stainless steel
-
- Designed to effectively hold the wear ring in place
- Also known as wear ring liners
-
- Create a double seal with these shouldered wear rings
- Over sizes available to fit your used impeller
- Fits American Turbine, Aggressor, Berkeley, and Dominator Late Model (1" skirt length) jet drive pump with new impeller
- A "standard" size wear ring is 7.250"
-
- Create a double seal with these shouldered wear rings
- Over sizes available to fit your used impeller
- A "standard" size wear ring is 7.250"
-
- Hand hole cover O-ring
-
- Made of stainless steel
-
- 3/8" Heavy Duty Hand Hole Cover Eye Bolts are Recommended for use on "RACE Application Pumps"
- Fits Berkeley pumps and American Turbine SD312 jet pumps
- Includes:
- Billet eye bolts
- Clevis Pins
- Cotter Pins
- Thick Washers
- Lock Washers
- Wing Nuts
-
This item fits OEM Berkeley only.
-
-
This item is out of stock, but, check out our used parts section.
-
- Made of Stainless Steel
-
- Made of stiainless steel
-
- Most jet pumps use 4 to 5 rings
- Sold per set of 5
-
- This is the piece that is behind the thrust bearing
- It usually breaks due to over tightening
- Sold per pair
-
-
-
- Suction piece clipper seal
-
-
Made of stainless Steel
-
Economy
- Up to 350 horsepower
- Double row of balls
Standard
- For use on moderate applications up to 450 horsepower
- Double row bearing, 8 balls per row 16 total
Extreme Duty
- For use on 500+ horsepower
- Use in High Horsepower applications where severe axial thrust loads are present.
- 11 ball double row angular contact bearing
Filling slot faces motor
Care must be taken when installing bearing onto shaft, only press on inner race of bearing
-
- Driveshaft or bearing cap seal
-
-
High Performance Jet Pump Shaft
- For use in pumps not exceeding 400 h.p.
- Fits Berkeley, American Turbine, and Dominator
Extreme Duty Jet Pump Shaft — Made in the USA
- For use in pumps over 400.h.p.
- The bowl bushing area on the shaft is hard chrome to extend the life of the shaft. This keeps the seal and bushing areas from wearing into the stainless steel.
- 17-4 Jet pump shaft, is known to be the strongest in the industry
- A must for anyweekend warrior or your all out blown alcohol jet boat
- Fits Berkeley, American Turbine, Dominator
Optional Inducer Machining
- Click the optional box below and we will machine your shaft for an inducer.
-
-
Made of stainless steel.
-
-
- 1/4"-20 x 1-1/4"" Lg
-
-
- Made of stiainless steel
-
- Made of stainless steel
-
- Made of stainless steel
-
- 1/4"-20 x 2" lg.
-
- Made of stainless steel
-
- Made of stainless steel
-
-
- 5/16"-18 x 3/4" lg
-
-
- Lower cable control bellows
- Sold by the each
-
5/16"-18 x 2" lg.
-
- Made of stainless steel
-
- Made of stiainless steel
-
- Made of stainless steel
-
- Made of stainless steel
-
- Made of stainless steel
-
- Made of stainless steel
-