12JC
Fig. No. | Description | Qty. Required | Mfg. No. | Fig. No. | Description | Qty. Required | Mfg. No. | |
---|---|---|---|---|---|---|---|---|
1 | Aluminum Impellers | 1 | IMB**A | 30 | Bowl Seals | 1 | SL2003 | |
Stainless Steel Impellers | IMB**S | 31 | 3/4" Nyliner Bearings | 4 | B2007 | |||
2 | Bowl | 1 | H-2484 | 32 | Thrust Bearings | 1 | B1007 | |
3 | Suction Piece | 1 | H-1727 | 33 | Shaft Snap Rings | 1 | SH1507 | |
4 | Hand Hole Covers | 1 | M-4128 | 34 | Impeller Nuts | 1 | SH3507 | |
6 | Steerable Nozzle | 1 | L-4501 | 35 | 5/16" Pin with Grooves | 2 | S-14479 | |
7 | Packing Gland Followers | 1 | SC2507 | 36 | Grease Zerks | 1 | SC8801 | |
8 | Bearing Caps | 1 | SC2007 | 37 | Impeller Keys | 1 | SH3007 | |
9 | Reverse Bucket | 1 | L-4251 | 38 | Woodruff Keys | 2 | R5507 | |
10 | Pump Shafts | 1 | SH1107 | 39 | Barbed Connectors | 1 | S-14821 | |
11 | Bowl Bearing End Caps | 1 | SC9001 | 40 | 3/8"-24 x 2" HHCS | 2 | F06 24 16 HH | |
12 | Shaft Sleeve Slinger Ring for Pump Shafts | 1 | SH2507 | 41 | 3/8"-24 Locknuts | 2 | F06 24 LN | |
13 | Stainless Steel Shouldered Wear Rings | 1 | WR5000 | 42 | 5/16" Spring Lock Washers | 3 | F05 LW | |
Bronze Shouldered Wear Rings | WR5000 | 43 | 1/2"-13 x 1-1/4" HHCS | 8 | F08 13 10 HH | |||
14 | Plastic Insulators | 1 | WR6004 | 46 | 5/16"-18 x 1" SHCS | 3 | F05 18 08 SH | |
15 | Tiller Shaft | 1 | S-15396 | 47 | 5/16"-18 x 5/8" Set Screws | 1 | F05 18 05 SS | |
16 | Pins | 2 | BN2510 | 49 | 5/16" Flange Nuts | 2 | S-23680 | |
18 | Bowl To Suction Gaskets | 1 | G2006 | 50 | Fastener, Lock Wrench | 1 | S-14493 | |
19 | Bearing Cap Gaskets | 1 | G1502 | 51 | Fastener Screw | 2 | S-25599 | |
22 | Lock Wrench, Hand Hole Cover | 1 | S-11543 | 52 | Oil Reservoir Pipe Plugs | 2 | SC9902 | |
23 | Heavy Duty Hand Hole Cover Eye Bolt Kits | 2 | F06 16 EB | 53 | 5/16"-18 x 1-1/4" SHCS | 4 | F05 18 10 SH | |
24 | Rope Packing | 5 | SC3007 | 54 | Rudder Kit | 1 | RK0595 | |
25 | Hand Hole Cover O-Rings | 1 | O1002 | 59 | 5/16"-18 x 1/2" Set Screws | 1 | F05 18 04 SS | |
26 | Suction Seals | 1 | SL1507 | 60 | Nozzle O-Rings | 1 | O1502 | |
28 | Glacier Bowl Bearings | 2 | B1502 |
Items:
1–47 of 47,
per page
-
1 left in stock
These kits include everything you need to rebuild your jet pump.
Most Kits include:
- Bearing cap gasket
- Bearing Cap Seal with stainless steel spring
- Bowl bearings (2)
- Bowl gasket
- Bowl o-ring
- Bowl Seal with stainless steel spring
- Graphite rope packing rings (5)
- Hand hole cover o-ring
- Impeller nut
- Impeller shims
- Insulator
- Nozzle housing gasket
- Nozzle o-ring - PTFE
- Nyliner bearings (4)
- Suction Housing Shaft Seal with stainless steel spring
- Suction housing to intake gasket
- Transom gasket
- Bearing (Koyo Brand) our "standard" duty — (upgrade available to Extreme duty)
- Non-shouldered Stainless Steel Wear ring – (upgrade available to stainless steel shouldered or bronze shouldered wear rings)
-
These kits include everything you need to rebuild your jet pump.
Most Kits include:
- Bearing cap gasket
- Bearing Cap Seal with stainless steel spring
- Bearing snap ring
- Bowl bearings (2)
- Bowl gasket
- Bowl o-ring
- Bowl Seal with stainless steel spring
- Graphite rope packing rings (5)
- Hand hole cover o-ring
- Impeller nut
- Impeller shims
- Insulator
- Nozzle housing gasket
- Nozzle o-ring - PTFE
- Nyliner bearings (4)
- Suction Housing Shaft Seal with stainless steel spring
- Suction housing to intake gasket
- Transom gasket
- Non-shouldered stainless steel wear ring – (upgrade available to stainless steel shouldered or bronze shouldered wear rings)
- High Performance Thrust bearing
-
- Recommended for up to 450 h.p.
- See Stainless Steel Impellers for 450 h.p or more
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller
Impeller Selection Chart
-
- Recommended for 450+ h.p.
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller
-
- This custom fitting filled Hand hole cover is designed for RACE USE ONLY.
- The cover fits the contour of the suction housing almost perfect thus leaving no room for air to get trapped around the cover that creates cavitation
- (Requires machining locator nub out of suction housing)
- Fits Berkeley JC and Berkeley JG jet drive pumps (Not OEM) It's aftermarket
-
- This is the piece that is behind the thrust bearing
- It usually breaks due to over tightening
- Sold per pair
-
-
High Performance Jet Pump Shaft
- For use in pumps not exceeding 400 h.p.
- Fits Berkeley, American Turbine, and Dominator
Extreme Duty Jet Pump Shaft — Made in the USA
- For use in pumps over 400.h.p.
- The bowl bushing area on the shaft is hard chrome to extend the life of the shaft. This keeps the seal and bushing areas from wearing into the stainless steel.
- 17-4 Jet pump shaft, is known to be the strongest in the industry
- A must for anyweekend warrior or your all out blown alcohol jet boat
- Fits Berkeley, American Turbine, Dominator
Optional Inducer Machining
- Click the optional box below and we will machine your shaft for an inducer.
-
-
-
- Create a double seal with these shouldered wear rings
- Over sizes available to fit your used impeller
- Fits American Turbine, Aggressor, Berkeley, and Dominator Late Model (1" skirt length) jet drive pump with new impeller
- A "standard" size wear ring is 7.250"
-
- Create a double seal with these shouldered wear rings
- Over sizes available to fit your used impeller
- A "standard" size wear ring is 7.250"
-
- Designed to effectively hold the wear ring in place
- Also known as wear ring liners
-
This item is out of stock, but, check out our used parts section.
-
- Made of stainless steel
-
-
-
-
- 3/8" Heavy Duty Hand Hole Cover Eye Bolts are Recommended for use on "RACE Application Pumps"
- Fits Berkeley pumps and American Turbine SD312 jet pumps
- Includes:
- Billet eye bolts
- Clevis Pins
- Cotter Pins
- Thick Washers
- Locj Washers
- Wing Nuts
-
- Most jet pumps use 4 to 5 rings
- Made of graphite
- Sold per set of 5
-
- Hand hole cover O-ring
-
- Suction piece clipper seal
-
- Glacier bowl bearings
- Bowl bushings
- Sold per each
-
- Driveshaft or bearing cap seal
-
-
- Pin bushing 3/4" nyliners
- Sold per pair
- Also fits Place Diveters
-
-
- Choose: Steel or billet machined hard anodized aluminum
- Loctite® is recommended
-
- Made of stainless steel
-
-
-
-
-
- Made of stainless steel
-
- Made of stainless steel
-
- Made of stainless steel
-
- Made of stainless steel
-
- Made of stainless steel
-
Made of stiainless steel
-
- Made of stainless steel
-
This item is out of stock, but, check out our used parts section
-
This item is out of stock, but, check out our used parts section.
-
-
- Made of stainless steel
-
- Made of stiainless steel
-
-