Impellers & Inducers
-
This 1-13/16" super deep well socket will remove your impeller nut from Berekely, American Turbine, Dominator and possibly other jet pumps.
Socket drive size is 3/4".
Overall length is 9".
-
- Indexed Super Flow Inducer
- Race track proven
- Helps the hole shot and reduces cavitation
- Keeps your pump hooked up under extreme conditions
- Includes inducer, instructions, machine key, and tapered spacer.
- We highly recommend you send in your impeller and shaft to properly index the shaft for maximum flow.
-
Machining of your shaft is required
- For use in pumps over 400.h.p.
- Made in USA
- Made of heat treated cast 17-4 PH stainless steel, known to be the hardest and strongest in the industry.
- Blueprinting is available in two choices
-Standard Blueprint - Knife edge and weed cut outer diameter
-Extreme Blueprint - Knife edge and weed cut outer diameter, overlap is precision tuned
-
- Recommended for up to 450 h.p.
- See Stainless Steel Impellers for 450 h.p or more
- American Turbine Brand
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller
Impeller Selection Chart
Does not fit SD-312, use this link for SD-312 impellers.
-
1 left in stock
- Recommended for 450+ h.p.
- American Turbine Brand
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller
Will not fit a SD-312 use this link for SD312 impellers.
-
- Recommended for 450+ h.p.
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller
HIP Process is removing the hydrogren imbrittlement to reduce cracking
-
- Recommended for 450+ h.p.
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller
-
- The inducer Feeds 20% more water to the impeller
- Helps the hole shot
- Keeps your pump hooked up under extreme conditions
- No Need to remove the shaft anymore! Simply machine the impeller and Slide the inducer on sharing the same key as the impeller.
- Includes inducer, machine key, and instructions
-
Machining of your impeller is required
Additonal Services
- You can send us your impleller to be machined. Just click the box... I will send my impeller for machining
- Blueprinting is available
-
2 left in stock
- The Best Inducer money can buy for the quickest ET's
- Race track proven
- Helps the hole shot and reduces cavitation
- Keeps your pump hooked up under extreme conditions
- Includes inducer, instructions, machine key, and tapered spacer
-
Machining of your shaft is required
High Performance Inducer
- For use in pumps not exceeding 400 h.p.
- Made of 18-8, 316, or 316L stainless steel
Extreme Duty Inducer
- For use in pumps over 400.h.p.
- Made in USA
- Made of heat treated cast 17-4 PH stainless steel, known to be the hardest and strongest in the industry.
Additonal Services:
- You can send us your shaft to be machined. Just click the box... I will send my shaft for machining
- Blueprinting is available in two choices
-Standard Blueprint - Knife edge and weed cut outer diameter
-Extreme Blueprint - Knife edge and weed cut outer diameter, overlap is precision tuned
-
- Designed to effectively hold the wear ring in place
- Also known as wear ring liners
Use this link for a SD312 plastic insulator
-
- Recommended for up to 450 h.p.
- See Stainless Steel Impellers for 450 h.p or more
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller
Impeller Selection Chart
-
Impeller fits 12WJ Jacuzzi Jet Drive OEM (Original Equipment Manufacturer)
Recommended for up to 450 h.p.
Choose from the following sizes:
9-9/16" Dia. = A Cut
9-3/8" Dia. = B Cut
9-1/4" Dia. =C Cut
9-1/8" Dia. = D Cut
9" Dia. = E Cut
Sold per Each
-
22.5° Impeller fits Marine Power 750 / 753 Jet Pumps
Sold per Each
-
22.5° Impeller fits Marine Power X-Stream Jet Pumps
Sold per Each
-
24° Impeller fits Marine Power 750 series Jet Pumps
Sold per Each
-
24° Impeller fits Marine Power X-Stream Jet Pumps
Sold per Each
-
27° Impeller fits Marine Power X-Stream Jet Pumps
Sold per Each
-
27° Impeller fits Marine Power 750 / 753 Jet Pumps
Sold per Each
-
- Designed to effectively hold the wear ring in place
- Also known as wear ring liners
-
- Shim Kits for your shaft
- Includes 1 each of the following thicknesses: (0.005", 0.010", 0.020", 0.40", and 0.060")
Individual shaft shims are also available.
Note: OEM Berkeley pumps do not come with a shouldered wear ring. When adding a shouldered wear ring you will need these shims.
-
- 1/4" size
-
- 1/4" size
-
- Individual shims for your shaft
- Sold by the each
Choose from the following thicknesses:
- 0.005"
- 0.010"
- 0.020"
- 0.040"
- 0.060"
Shaft shim kits are also available.
Note: OEM Berkeley pumps do not come with a shouldered wear ring. When adding a shouldered wear ring you will need these shims.
-
Design your own "Do-It-Yourself" kit, includes everything you need.
Includes: Inducer, stock Berkeley shaft machined for inducer, standard thrust bearing, tapered spacer, machine key, snap ring, and slinger ring
- Bearing is pressed on the shaft
- Snap ring is installed
Included price varys depending on your pump mfg. / style.
Items marked updgrade are an additional charge and can be added in the drop down boxes below.
-
Is you impeller cut for the Easy to Install Inducer and you want to run without the inducer? or lend your to your impeller to a friend?
Order this tapered collar, it slides on the shaft by the impeller so you can use the impeller that was machined for Easy to Install Inducer without the inducer.
-
Replacement spacer for inducer choose from two sizes:
- 0.868" is standard replacement
- 1.300" length moves the inducer forward — This option requires additional machining of shaft and/or inducer
Does not fit the Easy Install Inducer. See Collar for Easy install Inducer Collar.
-
Replacement key for HM inducer
-
- Recommended for 450+ h.p.
We will Blueprint inlet and exit side of any impeller purchased from us or sent in to us.
Blueprinting produces solid water out of the exit nozzle rather than air bubbles which creates more thrust.
- Blueprint stage 1 — Inlet side of impeller
- Blueprint stage 2 — Inlet and exit sides of impeller