Shafts
-
High Performance Jet Pump Shaft
- For use in pumps not exceeding 400 h.p.
- Fits Berkeley, American Turbine, and Dominator
Extreme Duty Jet Pump Shaft — Made in the USA
- For use in pumps over 400.h.p.
- The bowl bushing area on the shaft is hard chrome to extend the life of the shaft. This keeps the seal and bushing areas from wearing into the stainless steel.
- 17-4 Jet pump shaft, is known to be the strongest in the industry
- A must for anyweekend warrior or your all out blown alcohol jet boat
- Fits Berkeley, American Turbine, Dominator
Optional Inducer Machining
- Click the optional box below and we will machine your shaft for an inducer.
-
-
-
-
-
- Individual shims for your shaft
- Sold by the each
Choose from the following thicknesses:
- 0.005"
- 0.010"
- 0.020"
- 0.040"
- 0.060"
Shaft shim kits are also available.
Note: OEM Berkeley pumps do not come with a shouldered wear ring. When adding a shouldered wear ring you will need these shims.
-
- Pump shaft assembly fits SD Pumps, SHA1201
- SD203
- SD309
- SD312
- Pump shaft assembly fits SD Pumps, SHA1201
-
- 1/4" size
-
These shaft repair sleeve kits fit Morita Funjet pumps. Care must be taken when installing these shaft repair sleeves. Morita Funjet pumps may require more than one repair sleeve to fix the shaft. We can also repair the Morita jetpump shaft for you. Contact us for details. 815-942-2600
-
Splined Impeller Shaft fits 12WJ Jacuzzi Jet Drive OEM (Original Equipment Manufacturer).
Sold per Each
-
- Indexed Super Flow Inducer
- Race track proven
- Helps the hole shot and reduces cavitation
- Keeps your pump hooked up under extreme conditions
- Includes inducer, instructions, machine key, and tapered spacer.
- We highly recommend you send in your impeller and shaft to properly index the shaft for maximum flow.
-
Machining of your shaft is required
- For use in pumps over 400.h.p.
- Made in USA
- Made of heat treated cast 17-4 PH stainless steel, known to be the hardest and strongest in the industry.
- Blueprinting is available in two choices
-Standard Blueprint - Knife edge and weed cut outer diameter
-Extreme Blueprint - Knife edge and weed cut outer diameter, overlap is precision tuned
-
- Choose: Zinc-Plated Steel or billet machined hard anodized aluminum
- Loctite® is recommended
-
- Glacier bowl bearings
- Bowl bushings
- Sold per each
-
- This is the piece that is behind the thrust bearing
- It usually breaks due to over tightening
- Billett aluminum
- Sold per pair
-
Sold Per EACH Piece
-
-
- 1/4" size
-
- Driveshaft or bearing cap seal
-
-
-
- Shim Kits for your shaft
- Includes 1 each of the following thicknesses: (0.005", 0.010", 0.020", 0.40", and 0.060")
Individual shaft shims are also available.
Note: OEM Berkeley pumps do not come with a shouldered wear ring. When adding a shouldered wear ring you will need these shims.
-
- No need to replace the entire shaft because of damage due to sand or lack of maintenance
- This repair sleeve allows you to repair the end of the shaft
- Repair sleeve is Hard Chromed on O.D.
- Fits most Jet Boat Shafts
- Requires Machining
- Machining is not included in the cost of the repair sleeve
-
- The inducer Feeds 20% more water to the impeller
- Helps the hole shot
- Keeps your pump hooked up under extreme conditions
- No Need to remove the shaft anymore! Simply machine the impeller and Slide the inducer on sharing the same key as the impeller.
- Includes inducer, machine key, and instructions
-
Machining of your impeller is required
Additonal Services
- You can send us your impleller to be machined. Just click the box... I will send my impeller for machining
- Blueprinting is available
-
2 left in stock
- The Best Inducer money can buy for the quickest ET's
- Race track proven
- Helps the hole shot and reduces cavitation
- Keeps your pump hooked up under extreme conditions
- Includes inducer, instructions, machine key, and tapered spacer
-
Machining of your shaft is required
High Performance Inducer
- For use in pumps not exceeding 400 h.p.
- Made of 18-8, 316, or 316L stainless steel
Extreme Duty Inducer
- For use in pumps over 400.h.p.
- Made in USA
- Made of heat treated cast 17-4 PH stainless steel, known to be the hardest and strongest in the industry.
Additonal Services:
- You can send us your shaft to be machined. Just click the box... I will send my shaft for machining
- Blueprinting is available in two choices
-Standard Blueprint - Knife edge and weed cut outer diameter
-Extreme Blueprint - Knife edge and weed cut outer diameter, overlap is precision tuned
-
Design your own "Do-It-Yourself" kit, includes everything you need.
Includes: Inducer, stock Berkeley shaft machined for inducer, standard thrust bearing, tapered spacer, machine key, snap ring, and slinger ring
- Bearing is pressed on the shaft
- Snap ring is installed
Included price varys depending on your pump mfg. / style.
Items marked updgrade are an additional charge and can be added in the drop down boxes below.