Fits American Turbine Brand
Fits these nozzles:
-
- Pin Bushing 3/4" nyliners
- Also fits Place Diveters
- Sold per pair
Standard
- Color is white nylon
High Performance
- Color is grey
- More abrasion resistant than white nylon
- Low Friction Finish (Slippery)
-
- Made of Stainless steel
- Includes two wood screws
- Also known as cable packing seals
-
- Also known as rod end bearings
-
Complete assembly (as pictured).
-
A must when adding a droop snoot or bowl extension.
- Length is measured center-to-center
Need a complete kit? Our steering extension kits
-
This 7" steering extension kit is all you need.
- Kit is designed to be used with Berkley Style Droop Snoot Housing
- Includes: steering swivel, riser tube, and steering tube Extension
Need just the steering swivel and riser tube click here?
-
- Nozzle O-ring for steering nozzle
- Not sure which thickness you need????? Go grab two nickels and a quarter.
- If all this change fits in the slot then you need the 7/32" oring (see second picture).
- If only two nickels fit order the 1/8" one.
- If the nickel/quarter method doesn't work for you, give us a call at 815-942-2600 and we can help you.
-
- With a touch of the up / down button it provides ultimate trim control from the steering wheel
- Use on hydraulic jack plates, Place Diverters, trim tabs, or motor trim
- Includes 11" curly cord which can stretch to 48" uncoiled
- Easily mounts to the steering wheel or dashboard.
- Includes instructions, fasteners, wire nuts and "diodes"
-
- Up / down momentary push button
- 18" straight cord wiring harness
- Use on applications such as hydraulic jack plates, trim tab or motor trim
- Does not include diodes.
- We also offer a curly cord diverter switch with diodes.
-
- Pin Bushing 3/4" Nyliners
- High Performance Grey
- Sold per pair.
-
- Complete bolt on system, gives bow attitude adjustment for faster holeshots and "on plane" speeds
- Creates a HUGE rooster tail
- Kit provides freedom of instant control with the flip of a switch
- American Turbine Brand
- Color is white
Each kit includes:
- Hydraulic diverter assembly
- Hydraulic pump
- Hydraulic Cylinder
- Nozzle Insert
- Wiring harness
- Switch
- Brass Compression Fittings
- Plastic hydraulic lines
- Water tight fittings (pair)ylinder with stainless steel heim end (rod bearing)Dovetail mounting backet
- In-line fuse
- 3-way electrical switch
-
- These brass fittings go on the Place Diverter or American Turbine hydraulic cylinder
- Made of brass
- Sold per pair
-
- These brass fittings go on the Place Diverter or American Turbine hydraulic cylinder
- Made of brass
- Sold per pair
-
Easy to install:
- Drill two 7/16" dia. holes in your transom, or transom adapter ring
- Use a 1/2"-20 tap to thread holes
- Apply Life Seal (silicone) to threads of fitting,and screw into threaded holes
- Slide tubing through hole and when at desired length turn outer lock nut tight
Sold per pair
-
- Made of high pressure plastic tubing
- Connects your hydraulic pump to your cylinder
- Approximate 14' length
-
- Ultimate braided line kit runs from the Droop Snoot or Nozzle Housing to the Transom
- Aircraft quality stainless steel lines, includes everything to install your existing diverter
- Includes bulk head fittings, just drill your transom to install and reconnect lines to cylinder
Choose from two Styles:
- For Standard Nozzle Housings — Includes 22" and -26" length hoses
- For Droop Snoots — Includes 30" and 34" length hoses
Choose from two Fitting Styles:
- All stainless steel hydraulic lines
- Stainless steel to plastic lines]
Also availble:
- Inside Kit includes 2 hydraulic lines connecting the transom to the hydraulic pump, two 90° fittings for the pump, and two flared bulk head fittings
- Complete kit — Includes:
4 stainless steel hydraulic lines. Two from the nozzle housing or droop snoot to the transom. Two additional from the transom to the hydraulic pump.2 bulk head fittings, just drill your transom to install and reconnect lines to cylinder
Four 90° Fittings
-
- Everything you need to mount your hydraulic pump to your boat
-
- Cover fits all Place Diverter or American Turbine Diverter hydraulic pumps
- Replace your cracked cover, with a nice new one
-
- Stainless Steel cylinder
- Picture shows:
Optional brass compression fittings
Optional prod end bearing (heim end)
Optional top mount bolt and nut
- Can be used with air for many other functions such as exhaust flapper control, or reverse bucket controls
- Fits Place Diverter or American Turbine Diverter
-
1 left in stock
- Hydraulic pump used to control Place Diverters or American Turbine Diverters.
- Specially designed to for Place Diverters with 4 solenoid valves. The extra 2 solenoids hold the up or down position in place.
- Very dependable
Easy to install
-Fill with any type of transmission fluid
-Turn the switch up and down about six times
-Line will self bleed
Includes hydraulic pump only
-
Kit includes:
- Hydraulic pump wire harness
- Hydraulic pump plastic line (approx. 14')
- Stainless steel cylinder with rod bearing end (heim)
- Dovetail mounting bracket and hardware
-
- Mounts to your dash, for easy finger tip control
- For use with Place Diverter or American Turbine Diverters
-
- This steering arm has an extra offset to keep the steering cable straighter
- Offers a slightly higher steering connection
- Steering standard arm mounts to the top of your Place Diverter with 2 allen screws
- Great for hooking up an American Turbine steering assembly or American Turbine transom housings
- Available in manual control or hydraulic control
- Fits all Aggressor, American Turbine, Berkeley 12JA, 12JB, 12JC, and 12JG, Dominator, Legend, and Volvo Penta
-
- Made of stainless steel
-
Push button activated steering wheel controlled C02 solenoid valve fits Ram Horn Reverse Buckets, Long Horn Neutral Buckets, and can be modified to fit Place Diverters (also can fit American Turbine Diverters)
Kit includes:
- Push button steering wheel control
- C02 solenoid valve
- Relay assembly
- 15' wiring harness
- Attached to mounting plate
-
- Ultimate braided line kit is contains quality stainless steel lines and everything to install your existing diverter
- Includes:
- 4 stainless steel hydraulic lines. Two from the nozzle housing or droop snoot to the transom. Two additional from the transom to the hydraulic pump.
- 2 bulk head fittings, just drill your transom to install and reconnect lines to cylinder
- Four 90° Fittings
Choose from two Styles:
- For Standard Nozzle Housings — Includes 22" and -26" length hoses
- For Droop Snoots — Includes 30" and 34" length hoses
Choose from two Fitting Styles:
- All stainless steel hydraulic lines
- Stainless steel to plastic lines
Also availble:
- Inside Kit includes 2 hydraulic lines connecting the transom to the hydraulic pump, two 90° fittings for the pump, and two flared bulk head fittings
- Outside Kit includes 2 hydraulic lines connecting the Droop Snoot or Nozzle Housing to the Transom, two 90° fittings , and two bulk head fittings
-
The is cable end steering swivel is made of alumimum. The steering swivel also has a brass bushing.
-
- Includes: steering swivel and riser tube
- Riser Tube is 2 inches tall
Need the entire kit with steering extension click here